Bai BA-220 Especificações

INSTALLATION AND MAINTENANCE MANUAL FOR BA-220 DualBeam BARCODE READER revised 1/31/2009 800-528-9167 407-327-2177 FAX 40

Copyright 1999-2009, Barcode Automation, inc. 10 Basic Installation and Setup steps 1. Determine where the Reader will be installed 2. Run wiring to

Copyright 1999-2009, Barcode Automation, inc. 11 Determine where the BA-220 DualBeam will be installed: In this side view, the important dimension i

Copyright 1999-2009, Barcode Automation, inc. 12 Determine where the BA-220 DualBeam will be installed: In some locations the vehicle drive

Copyright 1999-2009, Barcode Automation, inc. 13 What Wiring do I need? For most applications, there are three basic ways to use the BA-220 DualBeam

Copyright 1999-2009, Barcode Automation, inc. 14 What Wiring do I need? In this situation the BA-220 DualBeam is connected to an external Access Cont

Copyright 1999-2009, Barcode Automation, inc. 15 What Wiring do I need? Continued… In this application the BA-220 DualBeam is connected to a Computer

Copyright 1999-2009, Barcode Automation, inc. 16 9"34"6"40"24"35"67"Typical Installation Illustration With a 34” m

Copyright 1999-2009, Barcode Automation, inc. 17 Connections for 115VAC unit Heater and FanGNDTxRxReset Default Com Serial

Copyright 1999-2009, Barcode Automation, inc. 18 Connections for 24VDC unit Heater and FanGNDTxRxReset Switch Default Com

Copyright 1999-2009, Barcode Automation, inc. 19 Surge Module Installation Detail Heater and FanGNDTxRxConnect to AC power

Copyright 1999-2009, Barcode Automation, inc. 2 FOREWORD The purpose of this manual is to provide information on how to install, configure, operate,

Copyright 1999-2009, Barcode Automation, inc. 20 Surge Module Replacement Instructions Surge Protection modules from BAI are sacrificial - if a power

Copyright 1999-2009, Barcode Automation, inc. 21 Surge Module Replacement Instructions Important Safety Note: Turn reader power off before installin

Copyright 1999-2009, Barcode Automation, inc. 22 Connecting to the BA-220 DualBeam 115VAC power input The power input terminal block for 115VAC inpu

Copyright 1999-2009, Barcode Automation, inc. 23 Connecting to the BA-220 DualBeam Input/Output connections The No Read and Good Read output termina

Copyright 1999-2009, Barcode Automation, inc. 24 Finishing the BA-220 DualBeam Installation After the Reader is mounted and the wiring is connected,

Copyright 1999-2009, Barcode Automation, inc. 25 Mounting Angle Powering Up the BA-220 DualBeam When testing the BA-220 DualBeam

Copyright 1999-2009, Barcode Automation, inc. 26 LED Indicators Look on the left hand edge of the decoder circuit board (the one that has the gold wh

Copyright 1999-2009, Barcode Automation, inc. 27 LED Indicators Continued… Important: The BA-220 DualBeam will not read the exact same barcode numbe

Copyright 1999-2009, Barcode Automation, inc. 28 Barcode Label Placement on Vehicles 1. Always place the decals on the same side of the vehicle that t

Copyright 1999-2009, Barcode Automation, inc. 3 INTRODUCTION This section contains information for proper installation, operation and maintenance of t

Copyright 1999-2009, Barcode Automation, inc. 4 WARNING Use of controls, adjustments or performance of procedures other than those specified herein ma

Copyright 1999-2009, Barcode Automation, inc. 5 REQUIRED MAINTENANCE The BA-220 DualBeam laser window should be cleaned both inside and outside as ne

Copyright 1999-2009, Barcode Automation, inc. 6 CAUTION LASER LIGHT DO NOT STARE INTO BEAM 658nm LASER DIODE 1.0 MILLIWATT MAX. OUTPUT CLASS II LAS

Copyright 1999-2009, Barcode Automation, inc. 7 Contents Foreword ... 2 Intr

Copyright 1999-2009, Barcode Automation, inc. 8 General Specifications INPUT POWER For 115VAC input: Voltage 100 - 125VAC, 50 - 60 Hz

Copyright 1999-2009, Barcode Automation, inc. 9 General Specifications READ TRIGGER Continuous Scan Loop Detector Input OPTICAL Reading area begins